北京生物医学工程

婴儿辐射保暖台床面温度场仿真研究

Simulation study of temperature distribution on mattress for infant radiant warmer

作者：何栋王琪林定余杨海仕胡燕海

单位：宁波大学机械工程与力学学院（浙江宁波315211）<p>宁波戴维医疗器械股份有限公司（浙江宁波 315712）</p>

关键词：婴儿辐射保暖台；热辐射；温度均匀性；数值模拟；有限元方法；仿真

分类号：R318.01

出版年·卷·期（页码）：2019·38·1（22-27）

摘要：

目的通过数值模拟（numerical simulation）得到床面温度场结果，并与试验比较，探讨有限元方法（finite element methods，FEM)应用于保暖台温度场分析的可行性，从而为使用数值模拟方法辅助该类产品结构的优化设计提供参考价值。方法本文使用三维软件SOLIDWORKS建立了当前D公司某型号辐射保暖台的相关模型，然后导入ANSYS中，对保暖台在20℃环境以及全功率工作状态下的床面温度场进行有限元仿真，获得了主要测试点的温度数值及均匀性的仿真结果。与此同时，实际采用多通道温度记录仪和红外热像仪对床面的主要测试点及整体温度场进行记录，最后对仿真与试验数据进行误差分析。结果使用合理的计算方法得到仿真与试验测试点的误差率均在10%以内，且温度场的分布趋势也基本一致，验证了该有限元仿真方法有效。结论该有限元仿真方法所得数值比较准确，能够提前预测辐射温度场，辅助保暖台产品结构的优化设计。

Objective To discuss the feasibility of finite element methods(FEM) in thermal analysis of radiant warmer, and to provide reference value for using numerical simulation to assist in optimization and design of products, the simulation of temperature distribution on mattress is compared with experiment.Methods Using three-dimension software SOLIDWORKS a radiation warmer heating device model of D company was built, which was then imported into ANSYS to simulate the mattress distribution under the conditions of 20℃ and full power operation. Thetemperature values and uniformity of main test points were obtained in simulation. Meanwhile, muti-channel temperature recorder and infrared camera were used for experiment to record the values of test points and temperature field. The deviation of simulation and experiment was analyzed at last. Results Error rates of test points in simulation and experimentwere all within 10% and the distribution of temperature field was consistent, which proved that FEM analysis was valid. Conclusions FEM obtains accurate numerical values, which can be used to predict the temperature distribution and assist the optimal design of radiant warmer products.

参考文献：

[1]王阳,水珊珊,王霞.远红外在生物医学临床上的应用及其作用机制[J].科技导报,2014,32(30):80-84.

Wang Y, Shui SS, Wang X. Molecular mechanism of far-infrared therapy and its application in biomedicine[J]. Science and Technology Review,2014,32(30):80-84.

[2]林丽妮,陈慈,黄巧燕.远红外辐射保温台与婴儿培养箱保暖对早产儿生命体征及体质量的影响[J].中国中西医结合儿科学,2016,8(1):120-122.

Lin LN, Chen C, Huang QY. Effect of far-infrared radiation heat preservation and infant incubator to keep warm on the vital signs and body quality of premature infants[J]. Chinese Pediatrics of Integrated Traditional and Western Medicine, 2016,8(1):120-122.

[3] Fic AM, Ingham DB, Ginalski MK, Nowak AJ, Wrobel L. Heat and mass transfer under an infant radiant warmer—development of a numerical model[J]. Medical Engineering and Physics,2010,32(5):497-504.

[4]RoongprasertK,Phasukkit P, Pintavirooj C,et al.Heat and mass transfer of infant radiant warmer by computer simulation[C].Biomedical Engineering International Conference.IEEE,2013:1-4.

[5]Marek R,Ireneusz S.Numerical and experimental analysis of infant radiant warmer[J].Computer Assisted Mechanics and Engineering Sciences,2013, 20(3): 237-265.

[6]YY 0455-2011，医用电气设备第2部分：婴儿辐射保暖台安全专用要求[S].中国标准出版社，2013.

YY 0455-2011, Medical electrical equipment-part2: particular requirements for the safety of infant radiant warmers[S].Standards Press of China,2013.

[7]朱小芳,李红波,薛永胜.反射罩光学设计与均匀性仿真[J].光电技术应用, 2010, 25(6): 18-21.

Zhu XF, Li HB, Xue YS. Optical design and uniform simulation of reflector[J]. Electro-Optic Technology Application, 2010, 25(6): 18-21.

[8]杨世铭,陶文铨.传热学第四版[M].高等教育出版社,2006.

Yang SM, Tao WQ. The fourth edition of heat transfer[M].Higher Education Press,2006.

[9]何成.双光源选择性激光烧结预热与后固化工艺研究[D]西安：西安科技大学, 2013.

He C. Research on preheating and post-curing for selective laser sintering with dual light sources[D]. Xi'an：Xi'an University of Science and Technology,2013.

[10]王金龙. ANSYS12.0有限元分析与范例解析[M].北京:机械工业出版社, 2010.

Wang JL. Finite element analysis and case analysis of ANSYS 12.0[M]. Beijing: Mechanical Industrial Press, 2010.

[11]徐冰,马龙,郑兴林,王昭鑫.基于ANSYS对遥感器铝合金镜头低温环境试验技术的研究[J]. 航天器环境工程, 2012, 29(01): 32-37.

Xu B, Ma L, Zheng XL, Wang SX. Study on low temperature of the aluminum camera lens of remote sensor by ANSYS software[J].Spacecraft Environment Engineering, 2012, 29(01): 32-37.

[12]褚治德, 汪健生, 孟宪玲.红外加热辐射的基本理论与实践研究[C].锦州市光学学会.全国红外加热暨红外医学发展研讨会论文及论文摘要集.辽宁锦州：锦州市光学学会，2011: 10-15.

[13]饶连江.基于ANSYS的LED灯具热分析[J].照明工程学报, 2010, 21(1): 53-57.

Rao LJ. Thermal analysis for LED lamp based on ANSYS[J].China Illuminating Engineering Journal, 2010, 21(1): 53-57.

[14]任婷婷,胡德龙,张雯,等.婴儿辐射保暖台温度校准实验研究[J].计量技术,2016(6):50-52.

Ren TT, Hu DL, Zhang W, et al. Research on temperature calibration experiment of infant radiant warmer[J]. Measurement Technique, 2016(6):50-52.

[15]JFF1001-2011,通用计量术语及定义[S].北京:中国计量出版社,2011

JFF1001-2011,General measurement and definitions[S].Beijing: China Metrology Publishing House,2011.

服务与反馈：

【文章下载】【加入收藏】

提示：您还未登录，请登录！点此登录